Ti-10Cr合金析出相對硬度的影響
發布人：上海艾荔艾金屬材料有限公司www.bt990.com.cn
更新時間：2015-12-27
測試Ti-10Cr合金經900 ℃固溶及400~700 ℃時效后的維氏硬度，采用XRD和TEM分析析出相的成分及形貌，研究硬度、析出相特征與熱處理制度之間的關系。
Ti-10Cr合金析出相對硬度的影響Influence of precipitated phase on hardness of Ti-10Cr alloy測試Ti-10Cr合金經900 ℃固溶及400~700 ℃時效后的維氏硬度，采用XRD和TEM分析析出相的成分及形貌，研究硬度、析出相特征與熱處理制度之間的關系。結果表明：經900 ℃固溶空冷后，析出相為細小、彌散的等軸ω相和少量α相，合金硬度達到HV560；經400 ℃時效后，ω相和α相長大，合金硬度值稍有下降；經500 ℃時效后，ω相消失，α相長大為片狀，合金硬度明顯降低；當繼續升高時效溫度時，片狀α相會進一步長大，合金的硬度緩慢降低。
The Vickers-hardness of Ti-10Cr alloy was tested after being solution treated at 900 ℃ as well as following by aging treatment at 400?700 ℃. The precipitated phases and their morphologies during solution and aging were analyzed by XRD and TEM. Furthermore, the relationships among hardness, phase precipitation and heat treatment were discussed. The results indicate that the fine dispersion isothermal ω phase and few α phase form in the metastable beta matrix after solution treatment at 900 ℃ following by air cold. Under this condition, the hardness reaches HV560. ω phase and α phase grow after aging at 400 ℃, and the hardness shows a little decrease. ω phase is decomposed and α phase becomes lamella after aging at 500 ℃, and the hardness value of the alloy deceases remarkable. After that, with the increase of aging temperature, the hardness decreases slowly due to the α phase growth.
作為值得信賴的合作伙伴和高品質金屬合金的半成品供應商，艾荔艾擁有完善的服務體系和專業的團隊。在同客戶交易的過程中，我們力求根據不同的應用需求將我們的產品做到精益求精。針對當前和未來的市場需求，艾荔艾致力于為客戶提供最佳的金屬材料解決方案。
AILIAI has been a reliable partner and supplier of sophisticated and high-quality semi-finished products maed of alloys. In dialogue with our customers, we optimise our products to meet the specific application requirements. AILIAI develops the best alloy material solutions for current and future challenges.
獲取更多我們供應的合金和服務信息，請致電086-021-67660801或發電子郵件[email protected]聯系我們，您也可以通過微博和微信和我們互動。
For more information on the alloys and services that we supply,?call us?at 086-021-67660801 or email us at [email protected]. You can also get in touch on social media, we are constantly active on?Weibo?and?Weixin.