新聞資訊
熱軋TC21板材中α相形貌的演變
發布人：上海艾荔艾金屬材料有限公司www.bt990.com.cn
更新時間：2015-11-02
研究了具有片層α組織TC21鈦合金在β和α+β相區熱軋制后的組織演變規律及其片層組織的球化機制。
熱軋TC21板材中α相形貌的演變Evolution of α phase morphology in hot-rolling?TC21 titanium alloy plate
研究了具有片層α組織TC21鈦合金在β和α+β相區熱軋制后的組織演變規律及其片層組織的球化機制。結果表明：變形溫度及應變對具有片層α組織的TC21鈦合金斷裂及球化具有顯著影響。當變形溫度為990℃時，在β相區發生變形；當應變不小于0.51時，平行軋向和晶界附近的片層α組織首先發生斷裂、球化，晶內片層α組織被壓彎變形；當在接近相變點(即950 ℃)變形，應變達到0.92時，片層α組織發生球化；當在兩相區較低溫度，即910 ℃和870 ℃變形時，片層α取向雜亂，且被壓彎成“手風琴”狀，未發現球化。TEM觀察分析發現，具有α片層組織的TC21鈦合金球化過程是一個復雜過程，首先，通過動態回復或是晶界滑移使得α片層中形成α/α界面；然后，β相通過亞晶界楔入α片層，α片層解體；最后，通過物質末端遷移，發生球化。
The microstructure evolution and mechanisms of globularization of TC21 titanium alloy with lamellar structure were investigated during hot rolling in the β phase and α+β phase. The results show that the prominent effect of hot working parameters on the break-up and globularization of TC21 titanium alloy with lamellar structure is found. The α lamellar structure along the paralleling rolling orientation and adjacent grain boundaries is broken up and globularized and the intragranular α lamellar is buckled and kinked when TC21 titanium alloy is processed in β phase region (990℃) at strain no less than 0.51 and at 950 ℃ and strain 0.92. When TC21 titanium alloy is deformed at 910 ℃ and 870 ℃, α lamellar is buckled and kinked to become accordion. Then, by TEM analysis, it is found that the mechanism of globularization of TC21 titanium alloy with α lamellar is a comprehensive process that is firstly the formation of α/α interface by dynamic recovery or boundary splitting, secondly the disintegrating of α lamellar due to diffusing, and finally the globularization of α lamellar by termination migration.
以上資料由上海艾荔艾金屬材料有限公司提供，歡迎新老客戶來電洽購。
本文來自上海艾荔艾金屬材料有限公司http://www.bt990.com.cn，轉載請注明出處。