新聞資訊
GW01鋁合金管材的熱處理工藝
發布人：上海艾荔艾金屬材料有限公司www.bt990.com.cn
更新時間：2015-09-15
GW01鋁合金是在6061鋁合金基礎上研發的一種新型高強鋁合金。采用三因素三水平的正交實驗，研究了固溶溫度-時間、時效溫度、時效時間三因素對GW01鋁合金T6處理后力學性能的影響規律。
GW01鋁合金管材的熱處理工藝Heat treatment process of GW01 aluminum alloy pipe
GW01鋁合金是在6061鋁合金基礎上研發的一種新型高強鋁合金。采用三因素三水平的正交實驗，研究了固溶溫度-時間、時效溫度、時效時間三因素對GW01鋁合金T6處理后力學性能的影響規律。結果表明：隨著固溶溫度的提高和固溶時間的縮短，GW01鋁合金的抗拉強度、屈服強度和硬度均有大幅度提高，其伸長率則先降低后升高；隨著時效溫度的升高，GW01鋁合金的抗拉強度、屈服強度、硬度以及伸長率均不斷降低；GW01鋁合金的抗拉強度、屈服強度以及硬度均對時效時間不敏感，隨時效時間的延長只有小幅度的降低，其伸長率則隨時效時間的延長有一定幅度的提高。(510 ℃，3 h，水淬)+(170 ℃，18 h，空冷)的T6熱處理可以使GW01鋁合金管材獲得良好的綜合力學性能。
GW01 aluminum alloy is a new type of high-strength aluminum alloys researched and developed based on 6061 aluminum alloy. The effects of solid solution temperature-time, aging temperature and aging time on mechanical properties of GW01 aluminum alloy after T6 treatment were investigated by orthogonal experiment of three factors and three levels. The results show that, with the solution temperature increasing and solution time decreasing, the tensile strength, yield strength and hardness of GW01 aluminum alloy are improved greatly, and the elongation increases after a certain amount of decline. With the aging temperature increasing, the tensile strength, yield strength, hardness and elongation of GW01 aluminum alloy decrease constantly. The tensile strength, yield strength and hardness of GW01 aluminum alloy are all insensitive to aging time, which means that they only decreases a little with aging time extending. The elongation increases with aging time extending. The good mechanical properties of GW01 aluminum alloy pipe are obtained after T6 treatment process of (510 ℃, 3 h, water quenching)+(170 ℃, 18 h, air cooling).
以上資料由上海艾荔艾金屬材料有限公司提供，歡迎新老客戶來電洽購。
本文來自上海艾荔艾金屬材料有限公司http://www.bt990.com.cn，轉載請注明出處。
前一頁：流變壓鑄A380鋁合金的顯微組織與力學性能
后一頁：50Cr5MoV第三代鍛鋼支承輥用鋼中非金屬夾雜物及全氧