新聞資訊
磁場對厚板Ti-6Al-4V合金窄間隙TIG焊縫組織的影響
發布人：上海艾荔艾金屬材料有限公司www.bt990.com.cn
更新時間：2015-08-24
對56 mm厚Ti-6Al-4V合金進行窄間隙磁控電弧TIG焊接，通過金相顯微鏡對接頭各區組織進行對比分析。
磁場對厚板Ti-6Al-4V合金窄間隙TIG焊縫組織的影響Effect of magnetic field on weld structure of large
thickness Ti-6Al-4V alloy with narrow-gap TIG welding method
對56
mm厚Ti-6Al-4V合金進行窄間隙磁控電弧TIG焊接，通過金相顯微鏡對接頭各區組織進行對比分析。結果表明：在窄間隙的多層單道焊接中，接頭各區的組織、結晶形態及生長方向存在很大差異。焊縫區一次結晶組織為表層焊道上表面的柱狀粗大組織及熔合線附近、焊道內部的等軸晶組織。熔合線處，電磁作用提高了平面狀結晶前沿及后來形成的等軸晶的穩定性，最終隨著磁場強度的增加在熔合線附近逐漸由柱狀晶轉變?yōu)榈容S晶。焊縫中心處，磁控電弧作用使得生成的等軸晶穩定性提高，隨著磁場強度的增加，等軸晶逐漸單方向伸長，在熱傳導方向上，即焊縫表層垂直方向生成粗大的柱狀晶。
A narrow-gap controlling magnetic field TIG welding
experiment was conducted directing at the 56 mm-thickness Ti-6Al-4V titanium
alloy. Afterwards, an analysis was taken to compare each weld joint
microstructure by means of metallographic microscope. The results show that,
during the multilayer single channel of narrow gap welding, the joint
microstructure, the crystal structure and the growth orientation significantly
differ from each other. The first crystal structure in the weld zone is an
equiaxed grain which shows a columnar coarse grain at the top layer of the weld
surface and near the bond line and the internal weld. Since the electromagnetic
effect improves the stability of flat crystal and the equiaxed grains appear
afterwards, ultimately, there are equiaxed grains translated from coarse
columnar grains in the front of bond line with the magnetic field strength
increasing. Due to the effect of magnetic controlled arc on improving the
stability of equiaxed grains, along with the magnetic field strength increasing,
the equiaxed grains gradually extend in a single direction; in the direction of
heat conduction, i.e., in the vertical direction of the weld surface, the coarse
columnar grains generate.
以上資料由上海艾荔艾金屬材料有限公司提供，歡迎新老客戶來電洽購。
本文來自上海艾荔艾金屬材料有限公司http://www.bt990.com.cn，轉載請注明出處。
前一頁：7075鋁合金熱變形時動態再結晶晶粒度演化模型
后一頁：抽拉速率對定向凝固DZ483合金的微觀組織及力學性能的影響